chain saw are design to work with specialised lubricants specifically created for their components and operation . But in the absence of chainsaw oil , can you use motor oil colour ? We ’ve done our research , and here ’s the reply we find .
you could temporarily use motor oil in a chain saw to keep it running . However , it should have the appropriate SAE rating to assure it has the right viscosity level . remark that motor vegetable oil might not be the best lasting replenishment for chainsaw oil color .
A chainsaw is utile for a wide range of jobs , from pruning to tree diagram felling , bucking , and gameness . Keep reading to watch about the veracious oil to use for your chainsaw and the alternative you’re able to replace it with .
Yes , you may use motor fossil oil as achainsaw oilalternative , but it is not without its drawbacks . Motor oil is thicker than the oil used for chainsaws and can induce a meaning buildup of residue on interior engine parts .
This buildup can precede to reduced performance from the chainsaw and an increased hazard of malfunction or injury . Using motor oil color could also evacuate the warranty on your chain saw .
In addition , motor oil color is not biodegradable . It can contaminate the air and soil and damage plant and tree . This is why you must be careful about using motor rock oil on your chain saw when working with alive trees .
For optimum execution , using the good lubricant type when operating a chainsaw is important . The maker ’s instructions should outline what sort of lubricant should be used in the locomotive and chain bar , so it is good to come these guidelines closely .
What Oil is Best For Chainsaw?
Thebestoil will not only keep your chain saw hunt smoothly but will also help you avoid clogging and extend the life of your chainsaw . The salutary oil for your chainsaw is one made for a four - virgule locomotive . It will also require additives , especially a fuel stabilizer , to prevent atomic number 6 buildup .
It should have anti - wear corrosion and oxidisation inhibitor to slow up the oxidation process and keep the Sir Ernst Boris Chain and legal community lubricated . For chainsaws with a two - stroke engine , the best oil for your chainsaw is a semi - celluloid oil .
This is because it has splendid lubricate properties , even in rough weather conditions .
Oregon Chainsaw Bar and Chain Oil
Oregon Chainsaw Bar and Chain oil color is an uncolored oil that provides superior lubrication for saw chains and guide bar . It has been formulate to reduce detrition , minimise wear , egest rosin buildup and ensure maximum performance of your byword .
Made with a particular blend of urbane alkali oils , it help protect against rust and corrosion from moisture or water middleman . The exclusive linear package will increase the life of your bar and Ernst Boris Chain while aid to preclude gumming and plugging in extreme temperatures .
Check out the Oregon taproom and string oil color on Amazon
STP Premium Oil
STP Premium Oil is design to keep your chainsaw campaign swimmingly and efficiently . It check particular additive that serve protect against railway locomotive deposits , gum form - up , varnish , gook , and heat damage from extreme temperatures .
It is develop with atomic number 30 dialkyl dithiophosphate , which gives it maximal anti - wear - and - snag place .
Check out the STP Premium oil on Amazon
How Do I Know If My Chainsaw Needs Lubricant?
right lubrication is the tonality if you want to conserve the performance and longevity of your chainsaw . When you do not lube your chainsaw , you could likely experience a loss in great power and might even make your chainsaw to smoke .
To hump if your chain saw demand lubricator , check the oil reservoir on it to ascertain it is full . The oil man-made lake should be filled with the funnel that come with your chain saw .
Note that too much oil can pull in debris , which can affect chainsaw performance . So , the right oil measure in the chainsaw is the layer at which the funnel shape is filled up . verify you check for outflow in your oil artificial lake before you fill it up .
Another way of life to know if your chainsaw needslubricantis when there ’s overheating or friction . The string and bar of your chainsaw are in unremitting contact with one another .
Lubricants will facilitate to prevent friction and overheating . The general rule of ovolo is to oil your range of mountains and bar at least every meter you utilize your chain saw .
What Happens If I Use a Chainsaw Without Oil?
Using a chainsaw without vegetable oil can cause serious damage to your chainsaw . The more friction there is between the bar and the chain , the more heat is produced , and the more the concatenation and blades will wear out . The result of this is overheating , and more fuel is consumed .
Also , this heat can cause other problems , like melting plastic components around the Ernst Boris Chain sprocket . It can also cause the saw to smoke , which could cause damage to the Ernst Boris Chain tips .
Steps to Properly Lubricate a Chainsaw With Chainsaw Oil
Each chainsaw has its specification and mixing requirements . However , the general rule of thumb is to expend a 50:1 ratio for mixing chainsaw crude . tick off your product manual to see the specified mixing ratio for your chainsaw .
avert using cheap oil and natural gas to avoid complicatedness on your chainsaw . This section contain astep - by - stepguide on how to oil your chain saw with chainsaw oil .
For base hit , make certain you wear down the proper equipment when working with your chainsaw . Theprotectivesafety equipmentincludes a difficult hat , hearing shelter , and safety deoxyephedrine . Wearing non - slip shoe while working with a chainsaw is also a good idea .
1. Prepare The Chainsaw
The first stage is to place the chainsaw on level ground . you may use a flat table as an alternative to this . Then , proceed to remove the electric battery if it ’s a stamp battery - power chainsaw .
This prevent the chainsaw from accidentally starting on its own while lubricating it . For gas - powered chainsaws , ensure the railway locomotive is cooled down before lubricate it .
2. Locate The Oil Reservoir
Most chainsaws arrive with a disjoined oil color reservoir . control that you do not mistake the oil heart for the oil man-made lake . The reservoir cap is next to the handgrip , and all you have to do is to remove the reservoir cap to locate the oil artificial lake .
3. Add The Chainsaw Oil and Run It
Insert a funnel shape into the oil artificial lake and add the chainsaw oil into it . assure that the oil artificial lake is fill up up , but check that it is not overfilled .
Return the reservoir capital and launch the chainsaw for 5 minutes for the rock oil pump to distribute the chainsaw crude oil to the bar and chain .
If you have an galvanising chainsaw , you must check that that the chain is completely dry before you start work . You should always turn the chainsaw off in case of rain or nose candy . Chainsaws can overheat if they get flooded with water . They can also get damage by lightning .
What Other Alternatives Can I Use Instead of a Chainsaw Oil?
There areseveral alternativesyou can use instead of chainsaw oil colour . They include the followers :
Vegetable Oil
Vegetable oil is a good alternative to chainsaw oil . It is environmentally friendly and cheap . It is also a sticky , fairly gummy oil with a high ostentation point . However , it is not the best choice for long - full term use because it plunk at grim temperatures .
Canola Oil
Another adept alternative is canola oil . It is one of the sparse oils , which makes it easy to wash off . It is also similar to vegetable petroleum , except it perform well at low temperature .
It can also keep your chainsaw safe , with little to no smoke . However , it dry out faster than other oils . This means you will have to fill up your oil reservoir more often .
Soybean Oil
Soybean oil is another good substitute . It is not toxic and will extend the ledge life of your chainsaw . It is also a full pick for environmentally - conscious loggers because it is safe for humans and the environment .
Conclusion
Sometimes , using motor oil color as a chainsaw oil substitute can damage your chain saw . Motor oil colour should be your emergency resort hotel for lubricating your chainsaw , not your go - to lubricate option . Also , make certain you use fresh motor petroleum because an already - used one can contain junk that would clog your chain saw .
If you enjoyed reading this berth , suss out out other related to articles on chainsaw :
Why is My Chainsaw Automatic Oiler Not go ?
Should You Run a Chainsaw at Full Throttle ?
